|MSDS INFORMATION CAN BE FOUND HERE
SOLD IN: 1 Gallon Cans
Federal regulations prohibit the shipment of flammable products by air. They CANNOT be shipped by Next Day, 2nd Day, 3 Day or US MAIL services. These items can ONLY shipped by UPS Ground.
These items can only be shipped within the USA. These items cannot be shipped Internationally
The ideal contact cement for automotive interior applications. Its high heat resistance is well suited for adhering headliners, fabric, and many other materials during automobile refurbishment. Easy to apply with hot or cold spray equipment.
DAP WELDWOOD HHR Solvent Type Spray Grade Contact Cement is a sprayable contact adhesive especially developed to meet the
requirements of the automobile refurbishment after market business. DAP WELDWOOD HHR adhesive has excellent application properties and forms a high strength, high heat resistant bond that is resistant to water, many household chemicals and the effects of aging.
May be used to bond cloth, leather, laminates, wood veneers, upholstery, carpeting, headliners and many similar materials, to metal, rigid polyurethane foam, and fiberboard in automobile restoration and customizing.
- Excellent heat resistance
- Bond strenght increases with age
- Resists water and many household chemicals
- Up to 2 hours open time
- Approximately 200 sq. ft. coverage
- Over dried adhesive may be reactivated by applying another thin coat of adhesive
- Shelf Life: 12 months minimum at 70°F
- Use as supplied, DO NOT THIN
- Contact adhesive is not suitable for structural applications.
- May damage some plastics, test before use
- Do not use on copper, copper alloys, some vinyls or polysytyrene foam.
- Let adhesive assemblies cure for at least 72 hours before exposing to direct sunlight or temperature over
- Adhesive may gel if stored at low temperatures, but returns to normal viscosity at 70°F (21°C).
Surfaces to be bonded must be clean and dry, adhesive, and air temperature and surfaces should be at least 65°F
Fluid pressure should be 15 to 25 psi. Atomization air pressure should be 70 to 90 psi (80 to 100 psi for
HVLP). Use a standard or hot spray system to apply an even coat to both surfaces. Direct spray perpendicular
to the plane of the substrate from approximately 10 to 12 inches away. 80% coverage forms an effective bond.
100% coverage is recommended at the edges. Allow both coated surfaces to dry before bonding (approximately
2 to 3 minutes when hot sprayed and 5 to 10 minutes if conventional spray is used). When dry, the adhesive
will adhere to but not transfer to kraft paper pressed onto the adhesive surface. Sufficient coverage is indicated
by a glossy appearance. Two coats may be necessary for porous substrates. Index both pieces accurately.
Contact adhesives bond instantly on contact and work cannot be shifted into place. Apply pressure with a pinch
roller or rotary press (a minimum of 40 psi is suggested) with a pinch roller or rotary press. If not available, a 3
inch rubber hand roller may be used (working from center to edge). Roll in 2 directions at 90° angles to each
other. Apply as much pressure as possible, being careful not to crush core materials.
Federal regulations prohibit the shipment of flammable products by air. They CANNOT be shipped by Next Day, 2nd Day, 3 Day or US MAIL services. This item can ONLY shipped by UPS Ground.
Thanks for shopping with us!
Remember, We Are Your Vinyl Superstore!
We Are A 5-STAR Rated Yahoo Shopping Merchant!
See What Others Have To Say:
Note: All images are scanned, actual colors
and texture may vary slightly.
Although we check all orders before they leave our warehouse,
the Customer is responsible for inspecting all materials for defects,
or shortages before use. Please check your order immediately after receiving it.
We cannot and will not replace, or refund your order once you have cut or used the material.
All claims for shortages, or missing items after 30 days will not be honored.